Product family

LT-TG3

9 variants · Varies by size, stroke, closing force, opening force, force retention

LH-TC

About this product family

The manufacturer selection table lists the LT-TG3 three-finger centric grippers with T guides across sizes, A/B stroke configurations where offered, and standard/CFM/OFM force configurations. Consolidate the smaller organizational groups while retaining every exact product and its own specifications.

Compare variants

Values retain their source conditions and claim stage. A missing value means it has not been published in this catalogue.

Variant / modelAir consumption per double strokeIngress protectionMassMaximum air pressureMaximum axial force fzDetails & evidence
LT-TG3-64A-OFM

49 cm³Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.5 kgConfiguration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.65 MPaConfiguration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

880 NConfiguration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

49 cm³

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 49.0

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.5 kg

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
自重(kg) 0.5

Maximum air pressure

0.65 MPa

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.65

Maximum axial force fz

880 N

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 880

Maximum finger length

72 mm

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
手指最大长度(mm) 72

Maximum finger mass

0.35 kg

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.35

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

200 N

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
最小保持力(N) 200

Moment mx

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
力矩Mx(N·m) 32

Moment my

48 N·m

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
力矩My(N·m) 48

Moment mz

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
力矩Mz(N·m) 32

Opening / closing time

0.04/0.02 s

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
开/合时间(s) 0.04/0.02

Opening force

960 N

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
张开力(N) 960

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030004 LT-TG3-64A-OFM 6 / 960 200 3.5 5℃~90℃ 查看详情>>

Order code

F13030004

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030004 LT-TG3-64A-OFM 6 / 960 200 3.5 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

3.5 kg

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
建议工件重量(kg)① 3.5

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

6 mm

Manufacturer specification

Configuration: LT-TG3-64A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-OFM - 郑州领航机器人有限公司
单指行程(mm) 6
LT-TG3-64A-CFM

49 cm³Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.5 kgConfiguration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.65 MPaConfiguration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

880 NConfiguration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

49 cm³

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 49.0

Closing force

900 N

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
闭合力(N) 900

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
防护等级(IP) 40

Mass

0.5 kg

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
自重(kg) 0.5

Maximum air pressure

0.65 MPa

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.65

Maximum axial force fz

880 N

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 880

Maximum finger length

72 mm

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
手指最大长度(mm) 72

Maximum finger mass

0.35 kg

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.35

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

200 N

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
最小保持力(N) 200

Moment mx

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
力矩Mx(N·m) 32

Moment my

48 N·m

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
力矩My(N·m) 48

Moment mz

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
力矩Mz(N·m) 32

Opening / closing time

0.02/0.04 s

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
开/合时间(s) 0.02/0.04

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030003 LT-TG3-64A-CFM 6 900 / 200 3.5 5℃~90℃ 查看详情>>

Order code

F13030003

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030003 LT-TG3-64A-CFM 6 900 / 200 3.5 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

3.5 kg

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
建议工件重量(kg)① 3.5

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

6 mm

Manufacturer specification

Configuration: LT-TG3-64A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A-CFM - 郑州领航机器人有限公司
单指行程(mm) 6
LT-TG3-64A

27 cm³Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.45 kgConfiguration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

880 NConfiguration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

27 cm³

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
耗气量(cm3)(双程) 27.0

Closing force

700 N

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
闭合力(N) 700

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
防护等级(IP) 40

Mass

0.45 kg

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
自重(kg) 0.45

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

880 N

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
最大轴向力Fz(N) 880

Maximum finger length

80 mm

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
手指最大长度(mm) 80

Maximum finger mass

0.35 kg

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
手指最大重量(kg) 0.35

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Moment mx

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
力矩Mx(N·m) 32

Moment my

48 N·m

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
力矩My(N·m) 48

Moment mz

32 N·m

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
力矩Mz(N·m) 32

Opening / closing time

0.03/0.03 s

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
开/合时间(s) 0.03/0.03

Opening force

760 N

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
张开力(N) 760

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030002 LT-TG3-64A 6 700 760 / 3.5 5℃~90℃ 查看详情>>

Order code

F13030002

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13030002 LT-TG3-64A 6 700 760 / 3.5 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

3.5 kg

Manufacturer specification

Configuration: LT-TG3-64A; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-64A - 郑州领航机器人有限公司
建议工件重量(kg)① 3.5

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

6 mm

Manufacturer specification

Configuration: LT-TG3-64A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-64A - 郑州领航机器人有限公司
单指行程(mm) 6
LT-TG3-50A-OFM

22 cm³Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.29 kgConfiguration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

400 NConfiguration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

22 cm³

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 22.0

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.29 kg

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
自重(kg) 0.29

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

400 N

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 400

Maximum finger length

58 mm

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
手指最大长度(mm) 58

Maximum finger mass

0.18 kg

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.18

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

125 N

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
最小保持力(N) 125

Moment mx

16 N·m

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
力矩Mx(N·m) 16

Moment my

20 N·m

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
力矩My(N·m) 20

Moment mz

8 N·m

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
力矩Mz(N·m) 8

Opening / closing time

0.03/0.02 s

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
开/合时间(s) 0.03/0.02

Opening force

585 N

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
张开力(N) 585

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020003 LT-TG3-50A-OFM 4 / 585 125 2.1 5℃~90℃ 查看详情>>

Order code

F13020003

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020003 LT-TG3-50A-OFM 4 / 585 125 2.1 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

2.1 kg

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
建议工件重量(kg)① 2.1

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

4 mm

Manufacturer specification

Configuration: LT-TG3-50A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-OFM - 郑州领航机器人有限公司
单指行程(mm) 4
LT-TG3-50A-CFM

22 cm³Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.29 kgConfiguration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

400 NConfiguration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

22 cm³

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 22.0

Closing force

555 N

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
闭合力(N) 555

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.29 kg

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
自重(kg) 0.29

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

400 N

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 400

Maximum finger length

58 mm

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
手指最大长度(mm) 58

Maximum finger mass

0.18 kg

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.18

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

125 N

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
最小保持力(N) 125

Moment mx

16 N·m

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
力矩Mx(N·m) 16

Moment my

20 N·m

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
力矩My(N·m) 20

Moment mz

8 N·m

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
力矩Mz(N·m) 8

Opening / closing time

0.02/0.03 s

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
开/合时间(s) 0.02/0.03

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020002 LT-TG3-50A-CFM 4 555 / 125 2.1 5℃~90℃ 查看详情>>

Order code

F13020002

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020002 LT-TG3-50A-CFM 4 555 / 125 2.1 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

2.1 kg

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
建议工件重量(kg)① 2.1

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

4 mm

Manufacturer specification

Configuration: LT-TG3-50A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A-CFM - 郑州领航机器人有限公司
单指行程(mm) 4
LT-TG3-50A

12 cm³Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.26 kgConfiguration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

400 NConfiguration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

12 cm³

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
耗气量(cm3)(双程) 12.0

Closing force

430 N

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
闭合力(N) 430

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.26 kg

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
自重(kg) 0.26

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

400 N

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
最大轴向力Fz(N) 400

Maximum finger length

64 mm

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
手指最大长度(mm) 64

Maximum finger mass

0.18 kg

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
手指最大重量(kg) 0.18

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Moment mx

16 N·m

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
力矩Mx(N·m) 16

Moment my

20 N·m

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
力矩My(N·m) 20

Moment mz

8 N·m

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
力矩Mz(N·m) 8

Opening / closing time

0.02/0.02 s

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
开/合时间(s) 0.02/0.02

Opening force

460 N

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
张开力(N) 460

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020001 LT-TG3-50A 4 430 460 / 2.1 5℃~90℃ 查看详情>>

Order code

F13020001

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13020001 LT-TG3-50A 4 430 460 / 2.1 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

2.1 kg

Manufacturer specification

Configuration: LT-TG3-50A; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-50A - 郑州领航机器人有限公司
建议工件重量(kg)① 2.1

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

4 mm

Manufacturer specification

Configuration: LT-TG3-50A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-50A - 郑州领航机器人有限公司
单指行程(mm) 4
LT-TG3-40A-OFM

9 cm³Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.14 kgConfiguration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

200 NConfiguration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

9 cm³

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 9.0

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.14 kg

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
自重(kg) 0.14

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

200 N

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 200

Maximum finger length

45 mm

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
手指最大长度(mm) 45

Maximum finger mass

0.1 kg

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.1

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

98 N

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
最小保持力(N) 98

Moment mx

8 N·m

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
力矩Mx(N·m) 8

Moment my

10 N·m

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
力矩My(N·m) 10

Moment mz

4 N·m

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
力矩Mz(N·m) 4

Opening / closing time

0.03/0.02 s

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
开/合时间(s) 0.03/0.02

Opening force

373 N

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
张开力(N) 373

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010003 LT-TG3-40A-OFM 2.5 / 373 98 1.25 5℃~90℃ 查看详情>>

Order code

F13010003

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010003 LT-TG3-40A-OFM 2.5 / 373 98 1.25 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

1.25 kg

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
建议工件重量(kg)① 1.25

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

2.5 mm

Manufacturer specification

Configuration: LT-TG3-40A-OFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-OFM - 郑州领航机器人有限公司
单指行程(mm) 2.5
LT-TG3-40A-CFM

9 cm³Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.14 kgConfiguration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

200 NConfiguration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

9 cm³

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
耗气量(cm3)(双程) 9.0

Closing force

348 N

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
闭合力(N) 348

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.14 kg

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
自重(kg) 0.14

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

200 N

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
最大轴向力Fz(N) 200

Maximum finger length

45 mm

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
手指最大长度(mm) 45

Maximum finger mass

0.1 kg

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
手指最大重量(kg) 0.1

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Minimum holding force

98 N

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer warns the force-enhanced gripper alone does not establish a force-retention system; retaining pressure with additional equipment such as a pressure-holding valve is required where force holding is needed.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
最小保持力(N) 98

Moment mx

8 N·m

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
力矩Mx(N·m) 8

Moment my

10 N·m

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
力矩My(N·m) 10

Moment mz

4 N·m

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
力矩Mz(N·m) 4

Opening / closing time

0.02/0.03 s

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
开/合时间(s) 0.02/0.03

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010002 LT-TG3-40A-CFM 2.5 348 / 98 1.25 5℃~90℃ 查看详情>>

Order code

F13010002

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010002 LT-TG3-40A-CFM 2.5 348 / 98 1.25 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

1.25 kg

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
建议工件重量(kg)① 1.25

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

2.5 mm

Manufacturer specification

Configuration: LT-TG3-40A-CFM; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A-CFM - 郑州领航机器人有限公司
单指行程(mm) 2.5
LT-TG3-40A

5 cm³Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

IP40Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.13 kgConfiguration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

0.8 MPaConfiguration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

200 NConfiguration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

Full specifications
Source-backed claims

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Air consumption per double stroke

5 cm³

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
耗气量(cm3)(双程) 5.0

Closing force

250 N

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
闭合力(N) 250

Ingress protection

IP40

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
防护等级(IP) IP40

Mass

0.13 kg

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
自重(kg) 0.13

Maximum air pressure

0.8 MPa

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
最大气压(Mpa) 0.8

Maximum axial force fz

200 N

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
最大轴向力Fz(N) 200

Maximum finger length

50 mm

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
手指最大长度(mm) 50

Maximum finger mass

0.1 kg

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
手指最大重量(kg) 0.1

Minimum air pressure

0.4 MPa

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
最小气压(Mpa) 0.4

Moment mx

8 N·m

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
力矩Mx(N·m) 8

Moment my

10 N·m

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
力矩My(N·m) 10

Moment mz

4 N·m

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
力矩Mz(N·m) 4

Opening / closing time

0.02/0.02 s

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
开/合时间(s) 0.02/0.02

Opening force

275 N

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
张开力(N) 275

Operating temperature

5℃~90℃ °C

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010001 LT-TG3-40A 2.5 250 275 / 1.25 5℃~90℃ 查看详情>>

Order code

F13010001

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

3指抓手 - 郑州领航机器人有限公司
F13010001 LT-TG3-40A 2.5 250 275 / 1.25 5℃~90℃ 查看详情>>

Rated air pressure

0.6 MPa

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
额定气压(Mpa) 0.6

Recommended workpiece mass

1.25 kg

Manufacturer specification

Configuration: LT-TG3-40A; Calculated with friction coefficient 0.1 and safety factor 2; robot acceleration is not considered. This is not an unrestricted dynamic payload rating.

LT-TG3-40A - 郑州领航机器人有限公司
建议工件重量(kg)① 1.25

Repeatability

0.01 mm

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
重复精度(mm) 0.01

Single-finger stroke

2.5 mm

Manufacturer specification

Configuration: LT-TG3-40A; Manufacturer specification for this exact model; additional test conditions are not specified.

LT-TG3-40A - 郑州领航机器人有限公司
单指行程(mm) 2.5

Related products

Contact Us

If you have any questions or would like to get in touch, please feel free to reach out to us at the email below.

info@robotuo.com

YOUR CHOICES

Privacy settings

Choose each optional purpose. All are off until you agree. Change or withdraw consent at any time; browsing still works if you reject all.

Privacy preference

Remembers the choice you make here.

Always active

Save comparisons and followed companies and products between visits. Turning this off deletes saved selections; you can still use them during this visit.

Allow Google Analytics through Firebase to measure general page visits and usage with cookies and device information. Advertising remains off.

Allow OneSignal to process browser and subscription information for Robotuo news and updates. Browser permission is a separate step.

Your shortlist

0 companies selectedUp to 10

Your shortlist is empty. Browse companies and add the ones you’d like to connect with.