Source-backed claims. Configuration, workload and evidence type matter when comparing products.
Creep 30 minutes
≤±0.5 %F.S./30 min
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Creep interval is 30 minutes, as printed in the header.
HPS-TSJ050-20 official technical page and embedded mechanical drawing蠕变
(%F.S./30min)
≤±0.5
Drawing angular spacing
45°
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawing45°
Drawing bore diameter
Φ14
+0.02
0
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ14
+0.02
0
Drawing inner drill
Φ2.5 through
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ2.5 完全贯穿
Drawing inner pitch circle
Φ19
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ19
Drawing inner step diameter
Φ24
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ24
Drawing inner threaded holes
8×M3-6H through
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawing8×M3-6H 完全贯穿
Drawing intermediate diameter
Φ38
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ38
Drawing outer counterbore
Φ4.3
2.3
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The two lines represent the diameter and depth adjacent to the counterbore/depth symbols.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ4.3
2.3
Drawing outer diameter
Φ50 h7
0
-0.025
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ50 h7
0
-0.025
Drawing outer mounting holes
12×Φ2.4 through
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawing12×Φ2.4 完全贯穿
Drawing outer pitch circle
Φ44
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawingΦ44
Drawing overall thickness
7±0.02
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ050-20 official technical page and embedded mechanical drawing7±0.02
Family card dimensions
φ50*7 mm
Manufacturer specification
Configuration: HPS-TSJ050-20; family card; Manufacturer family-card dimensional claim; the card uses mm. Diameter and axial thickness are shown in that order.
Hypersen Chinese force-sensor family and model summaryHPS-TSJ050-20扭矩传感器量程为20Nm,
产品尺寸为φ50*7mm,
可承受150%过载。
Hysteresis
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing滞后(%F.S.)
≤±0.5
Input resistance
700±5 Ω
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Insulation resistance
≥5000 MΩ
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. At 50 V DC, as explicitly printed. M is the mega prefix in the Ω row; value is 5000 MΩ, not 5000 Ω.
HPS-TSJ050-20 official technical page and embedded mechanical drawing绝缘电阻(Ω)
≥5000M(50VDC)
Nonlinearity
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing非线性(%F.S.)
≤±0.5
Operating temperature
-20~80 °C
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing工作温度(℃)
-20~80
Output resistance
750±50 Ω
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Output signal
0.8±1.6 mV/V
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Output alternatives are printed under one named model; no separately named hardware-interface variants are inferred. Analog sensitivities retain mV/V; RS485 is an interface, not a mV/V value. The printed tolerance exceeds the nominal sensitivity; retained literally, without correction.
HPS-TSJ050-20 official technical page and embedded mechanical drawing输出信号(mV/V)
0.8±1.6
Output type
Analog
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The dash footnote labels analog output; no sampling frequency is stated.
HPS-TSJ050-20 official technical page and embedded mechanical drawing–模拟量输出
Repeatability
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing重复性(%F.S.)
≤±0.5
Safe overload source limit
≤150 %F.S.
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The source literally prints an upper-bound sign ≤150; it is not silently changed to a guaranteed minimum overload rating.
HPS-TSJ050-20 official technical page and embedded mechanical drawing安全过载(%F.S.)
≤150
Sensitivity temperature coefficient
≤±0.5 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ050-20 official technical page and embedded mechanical drawing灵敏度温度系数((
%F.S./10℃
))
≤±0.5
Supply voltage
5~15 V DC
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing供电电压(V)
DC 5~15
Torque measurement range
20 N·m
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing量程(Nm)
20
Zero output
≤±1 %F.S.
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ050-20 official technical page and embedded mechanical drawing零点输出(%F.S.)
≤±1
Zero temperature coefficient
≤±0.1 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ050-20; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ050-20 official technical page and embedded mechanical drawing零点温度系数(
%F.S./10℃
)
≤±0.1