Source-backed claims. Configuration, workload and evidence type matter when comparing products.
Creep 30 minutes
≤±0.5 %F.S./30 min
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Creep interval is 30 minutes, as printed in the header.
HPS-TSJ042-25 official technical page and embedded mechanical drawing蠕变
(%F.S./30min)
≤±0.5
Drawing bore diameter
Φ12
+0.018
0
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ12
+0.018
0
Drawing cable connector
D0801H-5P
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingD0801H-5P
Drawing cable length
length 95mm
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. Cable length units are explicit in the literal note; other diameters in that note remain unit-unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing长度95mm
Drawing inner drill
Φ2.05 through
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ2.05 完全贯穿
Drawing inner pitch circle
Φ18
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ18
Drawing inner step diameter
Φ23
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ23
Drawing inner threaded holes
8×M2.5-6H through
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawing8×M2.5-6H 完全贯穿
Drawing intermediate diameter
Φ27
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ27
Drawing outer counterbore
Φ4.3
2.5
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The two lines represent the diameter and depth adjacent to the counterbore/depth symbols.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ4.3
2.5
Drawing outer diameter
Φ42
0
-0.04
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ42
0
-0.04
Drawing outer mounting holes
8×Φ2.4 through
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawing8×Φ2.4 完全贯穿
Drawing outer pitch circle
Φ34
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ34
Drawing overall thickness
6
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawing6
Drawing register diameter
Φ40
+0.025
0
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawingΦ40
+0.025
0
Drawing shoulder thickness
4.6±0.02
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ042-25 official technical page and embedded mechanical drawing4.6±0.02
Family card dimensions
φ42*6 mm
Manufacturer specification
Configuration: HPS-TSJ042-25; family card; Manufacturer family-card dimensional claim; the card uses mm. Diameter and axial thickness are shown in that order. The overview table prints HPS-TSJ042-35, but the current exact product page, its model row and the family card identify HPS-TSJ042-25. No separate 042-35 product is inferred.
Hypersen Chinese force-sensor family and model summaryHPS-TSJ042-25扭矩传感器量程为25Nm,产品尺寸为φ42*6mm,可承受150%过载。
Hysteresis
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing滞后(%F.S.)
≤±0.5
Input resistance
700±5 Ω
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Insulation resistance
≥5000 MΩ
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. At 50 V DC, as explicitly printed. M is the mega prefix in the Ω row; value is 5000 MΩ, not 5000 Ω.
HPS-TSJ042-25 official technical page and embedded mechanical drawing绝缘电阻(Ω)
≥5000M(50VDC)
Nonlinearity
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing非线性(%F.S.)
≤±0.5
Operating temperature
-20~80 °C
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing工作温度(℃)
-20~80
Output resistance
750±50 Ω
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Output signal
1.5±0.2 mV/V
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Output alternatives are printed under one named model; no separately named hardware-interface variants are inferred. Analog sensitivities retain mV/V; RS485 is an interface, not a mV/V value.
HPS-TSJ042-25 official technical page and embedded mechanical drawing输出信号(mV/V)
1.5±0.2
Output type
Analog
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The dash footnote labels analog output; no sampling frequency is stated.
HPS-TSJ042-25 official technical page and embedded mechanical drawing–模拟量输出
Repeatability
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing重复性(%F.S.)
≤±0.5
Safe overload source limit
≤150 %F.S.
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The source literally prints an upper-bound sign ≤150; it is not silently changed to a guaranteed minimum overload rating.
HPS-TSJ042-25 official technical page and embedded mechanical drawing安全过载(%F.S.)
≤150
Sensitivity temperature coefficient
≤±0.5 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ042-25 official technical page and embedded mechanical drawing灵敏度温度系数((
%F.S./10℃
))
≤±0.5
Supply voltage
5~15 V DC
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing供电电压(V)
DC 5~15
Torque measurement range
25 N·m
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing量程(Nm)
25
Zero output
≤±1 %F.S.
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ042-25 official technical page and embedded mechanical drawing零点输出(%F.S.)
≤±1
Zero temperature coefficient
≤±0.1 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ042-25; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ042-25 official technical page and embedded mechanical drawing零点温度系数(
%F.S./10℃
)
≤±0.1