Source-backed claims. Configuration, workload and evidence type matter when comparing products.
Creep 30 minutes
≤±0.5 %F.S./30 min
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Creep interval is 30 minutes, as printed in the header.
HPS-TSJ031-9 official technical page and embedded mechanical drawing蠕变
(%F.S./30min)
≤±0.5
Drawing bore diameter
Φ7
+0.015
0
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ7
+0.015
0
Drawing cable connector
D0801H-5P
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingD0801H-5P
Drawing cable length
length 80mm
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. Cable length units are explicit in the literal note; other diameters in that note remain unit-unspecified. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawing长度80mm
Drawing inner drill
Φ2.05 through
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ2.05 完全贯穿
Drawing inner pitch circle
Φ12
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ12
Drawing inner step diameter
Φ17
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ17
Drawing inner threaded holes
8×M2.5-6H through
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawing8×M2.5-6H 完全贯穿
Drawing intermediate diameter
Φ21
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ21
Drawing outer counterbore
Φ4.3
2.5
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The two lines represent the diameter and depth adjacent to the counterbore/depth symbols. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ4.3
2.5
Drawing outer diameter
Φ31.5
0
-0.04
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ31.5
0
-0.04
Drawing outer mounting holes
8×Φ2.4 through
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawing8×Φ2.4 完全贯穿
Drawing outer pitch circle
Φ26
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ26
Drawing overall thickness
5.5
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawing5.5
Drawing register diameter
Φ29.5
+0.025
0
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawingΦ29.5
+0.025
0
Drawing shoulder thickness
4.5±0.02
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
HPS-TSJ031-9 official technical page and embedded mechanical drawing4.5±0.02
Family card dimensions
φ31*5.5 mm
Manufacturer specification
Configuration: HPS-TSJ031-9; family card; Manufacturer family-card dimensional claim; the card uses mm. Diameter and axial thickness are shown in that order. The family card gives nominal diameter 31 mm while the embedded drawing prints an outer diameter of 31.5 with a tolerance; applicability is not resolved.
Hypersen Chinese force-sensor family and model summaryHPS-TSJ031-9扭矩传感器量程为9Nm,产品尺寸为φ31*5.5mm,可承受150%过载。
Hysteresis
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing滞后(%F.S.)
≤±0.5
Input resistance
700±5 Ω
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Insulation resistance
≥5000 MΩ
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. At 50 V DC, as explicitly printed. M is the mega prefix in the Ω row; value is 5000 MΩ, not 5000 Ω.
HPS-TSJ031-9 official technical page and embedded mechanical drawing绝缘电阻(Ω)
≥5000M(50VDC)
Nonlinearity
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing非线性(%F.S.)
≤±0.5
Operating temperature
-20~80 °C
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing工作温度(℃)
-20~80
Output resistance
750±50 Ω
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Output signal
1.0±0.5 mV/V
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Output alternatives are printed under one named model; no separately named hardware-interface variants are inferred. Analog sensitivities retain mV/V; RS485 is an interface, not a mV/V value.
HPS-TSJ031-9 official technical page and embedded mechanical drawing输出信号(mV/V)
1.0±0.5
Output type
Analog
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The dash footnote labels analog output; no sampling frequency is stated.
HPS-TSJ031-9 official technical page and embedded mechanical drawing–模拟量输出
Repeatability
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing重复性(%F.S.)
≤±0.5
Safe overload source limit
≤150 %F.S.
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The source literally prints an upper-bound sign ≤150; it is not silently changed to a guaranteed minimum overload rating.
HPS-TSJ031-9 official technical page and embedded mechanical drawing安全过载(%F.S.)
≤150
Sensitivity temperature coefficient
≤±0.5 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ031-9 official technical page and embedded mechanical drawing灵敏度温度系数((
%F.S./10℃
))
≤±0.5
Supply voltage
5~15 V DC
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing供电电压(V)
DC 5~15
Torque measurement range
9 N·m
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing量程(Nm)
9
Zero output
≤±1 %F.S.
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ031-9 official technical page and embedded mechanical drawing零点输出(%F.S.)
≤±1
Zero temperature coefficient
≤±0.1 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ031-9; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ031-9 official technical page and embedded mechanical drawing零点温度系数(
%F.S./10℃
)
≤±0.1