Product details

DM-S3519-1EC

Motors & Drives

Shenzhen Damao Technology Co., Ltd.

DM-S3519-1EC

About this product

DM-S3519-1EC is a DAMIAO geared motor with a separate drive for motion-control integration. The manufacturer places it in its discrete-motor range and describes a drive that supports motor replacement without recalibration; the cover depicts the motor component. Peak duration and duty cycle are not specified. An exact release date is not verified.

Model
DM-S3519-1EC
Category
Motors & Drives, Components

Specifications & evidence

Source-backed claims. Configuration, workload and evidence type matter when comparing products.

Can communication-loss protection

Exit enabled mode if no CAN command arrives within the configured interval

Manufacturer specification

Configuration: DM-S3519-1EC; The timeout is configurable; no numerical default is stated.

DM-S3519-1EC official table, visually transcribed
设定周期内没有收到CAN指令将自动退出“使能模式”

Can feedback

Motor speed, position, torque and temperature

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer exact-product feature statement.

DM-S3519-1EC_分立电机_产品中心_深圳市达妙科技有限公司
可通过CAN总线反馈电机速度、位置、转矩、电机温度等信息。

Control interface (published base table)

CAN

Manufacturer specification

Configuration: DM-S3519-1EC; Published base specification table.

DM-S3519-1EC official table, visually transcribed
控制接口 CAN

Control modes

MIT; speed; position

Manufacturer specification

Configuration: DM-S3519-1EC; Control-mode names translated from the official table.

DM-S3519-1EC official table, visually transcribed
控制模式 MIT模式 速度模式 位置模式

Drive overtemperature threshold

120 degC

Manufacturer specification

Configuration: DM-S3519-1EC; Protection threshold; drive overheating exits enabled mode. This is not an ambient temperature rating.

DM-S3519-1EC official table, visually transcribed
防护温度:120°C

Drive replacement behavior

Plug-and-play motor replacement without parameter recalibration

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer exact-product feature statement.

DM-S3519-1EC_分立电机_产品中心_深圳市达妙科技有限公司
驱动器智能化设计,更换电机后即插即用,无需重新校准和标定参数。

Encoder type

Incremental

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer specification for this model; additional measurement conditions are not stated.

DM-S3519-1EC official table, visually transcribed
编码器类型 增量式编码器

Height

91.5 mm

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer table dimension.

DM-S3519-1EC official table, visually transcribed
高度 电机91.5mm

Maximum can fd bitrate

5 Mbps

Manufacturer specification

Configuration: DM-S3519-1EC; Maximum supported CAN FD bitrate; network configuration is not specified.

DM-S3519-1EC_分立电机_产品中心_深圳市达妙科技有限公司
支持CAN FD功能,最高波特率可达5Mbps。

Maximum no-load speed

435 rpm

Manufacturer specification

Configuration: DM-S3519-1EC; Maximum speed under no load.

DM-S3519-1EC official table, visually transcribed
空载最大转速 435rpm

Maximum supported supply voltage

52 V

Manufacturer specification

Configuration: DM-S3519-1EC; supply range; Published supported supply range of the separate drive.

DM-S3519-1EC official table, visually transcribed
额定电压 24V(驱动支持15-52V供电)

Minimum supported supply voltage

15 V

Manufacturer specification

Configuration: DM-S3519-1EC; supply range; Published supported supply range of the separate drive.

DM-S3519-1EC official table, visually transcribed
额定电压 24V(驱动支持15-52V供电)

Motor mass

396 g

Manufacturer specification

Configuration: DM-S3519-1EC; Approximate manufacturer motor mass; not asserted to include a separate drive.

DM-S3519-1EC official table, visually transcribed
电机重量 约396g

Outside diameter

42 mm

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer table dimension.

DM-S3519-1EC official table, visually transcribed
外径 电机42mm

Parameter-tuning interface

UART@921600bps

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer specification for this model; additional measurement conditions are not stated.

DM-S3519-1EC official table, visually transcribed
调参接口 UART@921600bps

Peak phase current

20.5 A

Manufacturer specification

Configuration: DM-S3519-1EC; 24 V nominal configuration; Peak value; permitted duration and duty cycle are not stated.

DM-S3519-1EC official table, visually transcribed
峰值相/电源电流 20.5A(16.1A)

Peak supply current

16.1 A

Manufacturer specification

Configuration: DM-S3519-1EC; 24 V nominal configuration; Peak value; permitted duration and duty cycle are not stated.

DM-S3519-1EC official table, visually transcribed
峰值相/电源电流 20.5A(16.1A)

Peak torque

7.8 N m

Manufacturer specification

Configuration: DM-S3519-1EC; Peak value; duration and duty cycle are not stated.

DM-S3519-1EC official table, visually transcribed
峰值扭矩 7.8NM

Phase inductance

55 uH

Manufacturer specification

Configuration: DM-S3519-1EC; measurement method is not stated.

DM-S3519-1EC official table, visually transcribed
相电感 55uH

Phase resistance

0.2 ohm

Manufacturer specification

Configuration: DM-S3519-1EC; measurement method is not stated.

DM-S3519-1EC official table, visually transcribed
相电阻 0.2Ω

Pole pairs

7

Manufacturer specification

Configuration: DM-S3519-1EC; Manufacturer specification for this model; additional measurement conditions are not stated.

DM-S3519-1EC official table, visually transcribed
极对数 7

Rated phase current

9.2 A

Manufacturer specification

Configuration: DM-S3519-1EC; 24 V nominal configuration; Rated value; thermal and duty conditions are not stated.

DM-S3519-1EC official table, visually transcribed
额定相/电源电流 9.2A(8.6A)

Rated speed

395 rpm

Manufacturer specification

Configuration: DM-S3519-1EC; Rated manufacturer value; test setup and thermal conditions are not stated.

DM-S3519-1EC official table, visually transcribed
额定转速 395rpm

Rated supply current

8.6 A

Manufacturer specification

Configuration: DM-S3519-1EC; 24 V nominal configuration; Rated value; thermal and duty conditions are not stated.

DM-S3519-1EC official table, visually transcribed
额定相/电源电流 9.2A(8.6A)

Rated torque

3.5 N m

Manufacturer specification

Configuration: DM-S3519-1EC; Rated manufacturer value; test setup and thermal conditions are not stated.

DM-S3519-1EC official table, visually transcribed
额定扭矩 3.5NM

Rated voltage

24 V

Manufacturer specification

Configuration: DM-S3519-1EC; Nominal rated voltage. The manufacturer also supports the stated supply range.

DM-S3519-1EC official table, visually transcribed
额定电压 24V(驱动支持15-52V供电)

Recommended maximum motor-temperature setting

100 degC

Manufacturer specification

Configuration: DM-S3519-1EC; User-configurable motor-temperature protection setting; manufacturer recommends no more than 100 degrees C. Exits enabled mode on overheating.

DM-S3519-1EC official table, visually transcribed
建议不超过100°C

Recommended maximum overcurrent setting

20 A

Manufacturer specification

Configuration: DM-S3519-1EC; Configurable protection setting; exits enabled mode on overcurrent. Phase-current setting.

DM-S3519-1EC official table, visually transcribed
建议不超过20A(相电流)

Recommended maximum overvoltage setting

60 V

Manufacturer specification

Configuration: DM-S3519-1EC; Configurable protection recommendation; not normal operating voltage.

DM-S3519-1EC official table, visually transcribed
建议不超过60V

Recommended minimum supply voltage in undervoltage instructions

15 V

Manufacturer specification

Configuration: DM-S3519-1EC; Undervoltage-protection instruction; configurable trip threshold not stated.

DM-S3519-1EC official table, visually transcribed
电源电压不低于15V

Reduction ratio (manufacturer notation)

3591/187(1:19.2)

Manufacturer specification

Configuration: DM-S3519-1EC; The exact manufacturer ratio convention is retained; it is not inverted or reinterpreted.

DM-S3519-1EC official table, visually transcribed
减速比 3591/187(1:19.2)

Related products

Contact Us

If you have any questions or would like to get in touch, please feel free to reach out to us at the email below.

info@robotuo.com

YOUR CHOICES

Privacy settings

Choose each optional purpose. All are off until you agree. Change or withdraw consent at any time; browsing still works if you reject all.

Privacy preference

Remembers the choice you make here.

Always active

Save comparisons and followed companies and products between visits. Turning this off deletes saved selections; you can still use them during this visit.

Allow Google Analytics through Firebase to measure general page visits and usage with cookies and device information. Advertising remains off.

Allow OneSignal to process browser and subscription information for Robotuo news and updates. Browser permission is a separate step.

Your shortlist

0 companies selectedUp to 10

Your shortlist is empty. Browse companies and add the ones you’d like to connect with.