Source-backed claims. Configuration, workload and evidence type matter when comparing products.
Creep 30 minutes
≤±0.5 %F.S./30 min
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Creep interval is 30 minutes, as printed in the header.
HPS-TSJ068-300 official technical page and embedded mechanical drawing蠕变
(%F.S./30min)
≤±0.5
Drawing bore diameter
Φ14
+0.018
0
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ14
+0.018
0
Drawing cable length
length 2m
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. Cable length units are explicit in the literal note; other diameters in that note remain unit-unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing长度2m
Drawing inner counterbore
Φ8
4.6
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. The two lines represent the diameter and depth adjacent to the counterbore/depth symbols.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ8
4.6
Drawing inner mounting holes
8×Φ4.5 through
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawing8×Φ4.5 完全贯穿
Drawing inner pitch circle
Φ24
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ24
Drawing inner step diameter
Φ40
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ40
Drawing intermediate diameter
Φ34
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ34
Drawing locating holes
4-Φ4
+0.015
0
4
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. Stacked tolerance values follow the diameter; the final standalone value is the adjacent depth callout.
HPS-TSJ068-300 official technical page and embedded mechanical drawing4-Φ4
+0.015
0
4
Drawing outer blind hole
Φ8
+0.02
0
8
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions. Stacked tolerance values follow the diameter; the final standalone value is the adjacent depth callout.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ8
+0.02
0
8
Drawing outer diameter
Φ68
-0.01
-0.04
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ68
-0.01
-0.04
Drawing outer pitch circle
Φ55±0.1
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ55±0.1
Drawing outer threaded holes
8-M10 through
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawing8-M10通孔
Drawing overall thickness
13
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawing13
Drawing secondary pitch circle
Φ28±0.05
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page mechanical drawing; Literal callout from the mechanical drawing embedded by this exact product page. No explicit general linear-unit label is present, so no mm unit is inferred. Tolerances and fits are retained rather than converted to nominal-only dimensions.
HPS-TSJ068-300 official technical page and embedded mechanical drawingΦ28±0.05
Family card dimensions
φ68*13 mm
Manufacturer specification
Configuration: HPS-TSJ068-300; family card; Manufacturer family-card dimensional claim; the card uses mm. Diameter and axial thickness are shown in that order.
Hypersen Chinese force-sensor family and model summaryHPS-TSJ068-300扭矩传感器量程为300Nm,产品尺寸为φ68*13mm,可承受150%过载。
Hysteresis
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing滞后(%F.S.)
≤±0.5
Input resistance
700±5 Ω
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Insulation resistance
≥5000 MΩ
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. At 50 V DC, as explicitly printed. M is the mega prefix in the Ω row; value is 5000 MΩ, not 5000 Ω.
HPS-TSJ068-300 official technical page and embedded mechanical drawing绝缘电阻(Ω)
≥5000M(50VDC)
Nonlinearity
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing非线性(%F.S.)
≤±0.5
Operating temperature
-20~80 °C
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing工作温度(℃)
-20~80
Output resistance
750±50 Ω
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Source row order is output resistance / input resistance. Applicability to the internal bridge versus external digital interface is unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing输出/输入电阻(Ω)
750±50/700±5
Output signal
1.0±0.2 mV/V
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Output alternatives are printed under one named model; no separately named hardware-interface variants are inferred. Analog sensitivities retain mV/V; RS485 is an interface, not a mV/V value.
HPS-TSJ068-300 official technical page and embedded mechanical drawing输出信号(mV/V)
1.0±0.2
Output type
Analog
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The dash footnote labels analog output; no sampling frequency is stated.
HPS-TSJ068-300 official technical page and embedded mechanical drawing–模拟量输出
Repeatability
≤±0.5 %F.S.
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing重复性(%F.S.)
≤±0.5
Safe overload source limit
≤150 %F.S.
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. The source literally prints an upper-bound sign ≤150; it is not silently changed to a guaranteed minimum overload rating.
HPS-TSJ068-300 official technical page and embedded mechanical drawing安全过载(%F.S.)
≤150
Sensitivity temperature coefficient
≤±0.5 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ068-300 official technical page and embedded mechanical drawing灵敏度温度系数((
%F.S./10℃
))
≤±0.5
Supply voltage
5~15 V DC
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing供电电压(V)
DC 5~15
Torque measurement range
300 N·m
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing量程(Nm)
300
Zero output
≤±1 %F.S.
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified.
HPS-TSJ068-300 official technical page and embedded mechanical drawing零点输出(%F.S.)
≤±1
Zero temperature coefficient
≤±0.1 %F.S./10 °C
Manufacturer specification
Configuration: HPS-TSJ068-300; exact-page parameter table; Manufacturer exact-product HTML parameter table; test environment, electronics revision and calibration method are unspecified. Per 10 °C temperature change; no ambient reference temperature is printed.
HPS-TSJ068-300 official technical page and embedded mechanical drawing零点温度系数(
%F.S./10℃
)
≤±0.1