Source-backed claims. Configuration, workload and evidence type matter when comparing products.
Can communication-loss protection
Exits enabled mode if no CAN instruction arrives within the configured interval
Manufacturer specification
Configuration: DM-JH17-51-2EC; Timeout interval is configurable; no numerical default is stated.
DAMIAO JH17 technical parameter table通讯丢失防护,设定周期内没有收到CAN指令将自动退出“使能模式”
Can feedback
Motor speed, position, torque and temperature
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司可通过CAN总线反馈电机速度、位置、转矩、电机温度等信息。
Can upgrade
Supported
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司支持CAN升级。
Central bore size
15 mm
Manufacturer specification
Configuration: DM-JH17-51-2EC; Shared manufacturer table dimension for both reduction ratios.
DAMIAO JH17 technical parameter table中孔尺寸 15mm
Control interface
CAN; maximum 5 Mbps
Manufacturer specification
Configuration: DM-JH17-51-2EC; Table interface wording; the product-page feature text explicitly identifies CAN FD for the 5 Mbps maximum.
DAMIAO JH17 technical parameter table控制接口 CAN@5Mbps(Max)
Control modes
MIT; position-speed; speed; hybrid force-position; cyclic synchronous position; cyclic synchronous velocity; cyclic synchronous torque
Manufacturer specification
Configuration: DM-JH17-51-2EC; Control-mode names translated from this exact size table; position-speed is only printed for JH17, while JH11/JH14 print position.
DAMIAO JH17 technical parameter table控制模式 MIT 模式 位置速度模式 速度模式 力位混控模式 周期同步位置模式 周期同步速度模式 周期同步转矩模式
Drive overtemperature protection
100 degC
Manufacturer specification
Configuration: DM-JH17-51-2EC; Protection threshold; overheating exits enabled mode. Not an ambient operating-temperature rating.
DAMIAO JH17 technical parameter table驱动过温防护,防护温度:100°C,过温电机将退出“使能模式”
Encoder accuracy
±0.03 deg
Manufacturer specification
Configuration: DM-JH17-51-2EC; Published encoder accuracy; temperature, load and measurement method are not specified.
DAMIAO JH17 technical parameter table编码器精度 ±0.03 度
Encoder count
2
Manufacturer specification
Configuration: DM-JH17-51-2EC; Shared table value for the integrated actuator.
DAMIAO JH17 technical parameter table编码器个数 2
Encoder resolution
17 bit
Manufacturer specification
Configuration: DM-JH17-51-2EC; Encoder bit count; not itself an accuracy rating.
DAMIAO JH17 technical parameter table编码器位数 17 位
Height
70 mm
Manufacturer specification
Configuration: DM-JH17-51-2EC; Shared manufacturer table dimension for both reduction ratios.
DAMIAO JH17 technical parameter table高度 70mm
Housing-side mounting pitch-circle callout
74
Manufacturer specification
Configuration: DM-JH17-51-2EC; Diameter of the outer mounting circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing74
Housing-side mounting thread pattern
8 × M3
Manufacturer specification
Configuration: DM-JH17-51-2EC; Eight equally spaced threaded holes on the outer circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing8-M3
Housing-side thread depth callout
10.5
Manufacturer specification
Configuration: DM-JH17-51-2EC; Depth callout adjoining the outer-circle eight M3 threads. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing10.5
Integrated drive
Motor and drive integrated
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司电机和驱动器一体化设计,结构紧凑,集成度高。
Intermediate housing axial span callout
40
Manufacturer specification
Configuration: DM-JH17-51-2EC; Side-view span between the front housing shoulder and the indicated rear-body shoulder. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing40
Locating pin projection callout
2.2(max)
Manufacturer specification
Configuration: DM-JH17-51-2EC; Maximum locating-pin projection shown on the side view. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing2.2(max)
Main housing axial span callout
59
Manufacturer specification
Configuration: DM-JH17-51-2EC; Housing axial span excludes the output flange projection. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing59
Maximum can fd bitrate
5 Mbps
Manufacturer specification
Configuration: DM-JH17-51-2EC; Maximum CAN FD bitrate; network configuration and wiring conditions are not stated.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司支持CAN FD,最大波特率5Mbps。
Maximum permitted output speed
60 rpm
Manufacturer specification
Configuration: DM-JH17-51-2EC; Maximum permitted speed, not labelled as a no-load speed; other conditions are unspecified.
DAMIAO JH17 technical parameter table容许最大转速 60rpm | 30rpm
Motor mass
985 g
Manufacturer specification
Configuration: DM-JH17-51-2EC; Approximate mass as published; accessory inclusion is not stated.
DAMIAO JH17 technical parameter table电机重量 约 985g
Output flange diameter callout
62
Manufacturer specification
Configuration: DM-JH17-51-2EC; Output flange diameter, separate from the 80 mm overall diameter in the parameter table. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing62
Output locating pin pattern
4 × diameter 3; +0.02/0
Manufacturer specification
Configuration: DM-JH17-51-2EC; Four equally spaced locating-pin positions. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing4-⌀3 +0.02 0
Output mounting hole depth callout
10
Manufacturer specification
Configuration: DM-JH17-51-2EC; Depth callout for the eight diameter-3.2 holes. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing10
Output mounting hole pattern
8 × diameter 3.2
Manufacturer specification
Configuration: DM-JH17-51-2EC; Eight output mounting holes shown on the inner circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing8-⌀3.2
Output mounting pitch-circle callout
54
Manufacturer specification
Configuration: DM-JH17-51-2EC; Diameter of the output mounting circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing54
Output mounting thread depth callout
7.5
Manufacturer specification
Configuration: DM-JH17-51-2EC; Depth callout for the output M3 threads. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing7.5
Output mounting thread pattern
M3
Manufacturer specification
Configuration: DM-JH17-51-2EC; Thread callout alongside the eight diameter-3.2 holes. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawingM3
Output position retention
Single-turn absolute output position retained across power loss
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司双编码器,输出轴单圈绝对位置,不惧掉电输出轴绝对位置丢失。
Outside diameter
80 mm
Manufacturer specification
Configuration: DM-JH17-51-2EC; Shared manufacturer table dimension for both reduction ratios.
DAMIAO JH17 technical parameter table外径 80mm
Overcurrent protection recommendation
Configurable; recommended value no more than 0.98 (unit not specified)
Manufacturer specification
Configuration: DM-JH17-51-2EC; Overcurrent exits enabled mode. The manufacturer does not define the unit or parameter scale of 0.98; it is not interpreted as amperes or percent.
DAMIAO JH17 technical parameter table电机过流防护,根据使用需求设定,建议不超过0.98,过流将退出“使能模式”
Parameter access
Visual host tuning and CAN parameter read/write
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司支持上位机可视化调试,支持CAN读写参数。
Parameter-tuning interface
UART at 921600 bps
Manufacturer specification
Configuration: DM-JH17-51-2EC; Manufacturer parameter-tuning interface rate.
DAMIAO JH17 technical parameter table调参接口 UART@921600bps
Peak output torque
24 N m
Manufacturer specification
Configuration: DM-JH17-51-2EC; Peak output torque; permitted duration and duty cycle are not specified.
DAMIAO JH17 technical parameter table峰值扭矩 24NM | 54NM
Peak phase current
12.94 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 24 V supply; Peak current; permitted peak duration and duty cycle are not specified.
DAMIAO JH17 technical parameter table峰值相/电源电流 12.94A/7.88A@24V 12.94A/7.68A@48V | 16.85A/6.56V@24V 16.85A/3.72A@48V
Peak phase current
12.94 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 48 V supply; Peak current; permitted peak duration and duty cycle are not specified.
DAMIAO JH17 technical parameter table峰值相/电源电流 12.94A/7.88A@24V 12.94A/7.68A@48V | 16.85A/6.56V@24V 16.85A/3.72A@48V
Peak supply current
7.88 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 24 V supply; Peak current; permitted peak duration and duty cycle are not specified.
DAMIAO JH17 technical parameter table峰值相/电源电流 12.94A/7.88A@24V 12.94A/7.68A@48V | 16.85A/6.56V@24V 16.85A/3.72A@48V
Peak supply current
7.68 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 48 V supply; Peak current; permitted peak duration and duty cycle are not specified.
DAMIAO JH17 technical parameter table峰值相/电源电流 12.94A/7.88A@24V 12.94A/7.68A@48V | 16.85A/6.56V@24V 16.85A/3.72A@48V
Phase inductance
107 uH
Manufacturer specification
Configuration: DM-JH17-51-2EC; At 25 degrees C; measurement method is not stated.
DAMIAO JH17 technical parameter table相电感 107uH (@25°C)
Phase resistance
0.161 ohm
Manufacturer specification
Configuration: DM-JH17-51-2EC; At 25 degrees C; measurement method is not stated.
DAMIAO JH17 technical parameter table相电阻 0.161Ω (@25°C)
Pole pairs
10
Manufacturer specification
Configuration: DM-JH17-51-2EC; Shared cell spans both named reduction-ratio models.
DAMIAO JH17 technical parameter table极对数 10
Rated output speed
40 rpm
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rated speed for this reduction-ratio model; the shared table does not distinguish supply-voltage configurations for this row.
DAMIAO JH17 technical parameter table额定转速 40rpm | 20rpm
Rated output torque
16 N m
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rated output torque; mounting and thermal conditions are not specified.
DAMIAO JH17 technical parameter table额定扭矩 16NM | 24NM
Rated phase current
4.62 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 24 V supply; Rated current; test temperature, mounting and duty conditions are not specified.
DAMIAO JH17 technical parameter table额定相/电源电流 4.62A/4.04A@24V 4.62A/3.98A@48V | 6.31A/3.23A @24V 6.31A/1.72A @48V
Rated phase current
4.62 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 48 V supply; Rated current; test temperature, mounting and duty conditions are not specified.
DAMIAO JH17 technical parameter table额定相/电源电流 4.62A/4.04A@24V 4.62A/3.98A@48V | 6.31A/3.23A @24V 6.31A/1.72A @48V
Rated supply current
4.04 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 24 V supply; Rated current; test temperature, mounting and duty conditions are not specified.
DAMIAO JH17 technical parameter table额定相/电源电流 4.62A/4.04A@24V 4.62A/3.98A@48V | 6.31A/3.23A @24V 6.31A/1.72A @48V
Rated supply current
3.98 A
Manufacturer specification
Configuration: DM-JH17-51-2EC; 48 V supply; Rated current; test temperature, mounting and duty conditions are not specified.
DAMIAO JH17 technical parameter table额定相/电源电流 4.62A/4.04A@24V 4.62A/3.98A@48V | 6.31A/3.23A @24V 6.31A/1.72A @48V
Rated voltage
24 V
Manufacturer specification
Configuration: DM-JH17-51-2EC; Nominal rated voltage; the same source separately states a supported 24–48 V supply range.
DAMIAO JH17 technical parameter table额定电压 24V(支持24-48V)
Rear cover pitch-circle callout
61
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rear M4 mounting pitch-circle diameter callout. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing61
Rear cover thread depth callout
4.5
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rear M4 thread-depth callout. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing4.5
Rear cover thread pattern
4 × M4
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rear-cover threads; the drawing warns against using these to connect load-bearing structures. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing4-M4
Rear housing mounting pitch-circle callout
75
Manufacturer specification
Configuration: DM-JH17-51-2EC; Diameter of the rear outer mounting circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing75
Rear housing mounting thread depth callout
4
Manufacturer specification
Configuration: DM-JH17-51-2EC; Depth callout for the rear outer-circle M3 threads. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing4
Rear housing mounting thread pattern
8 × M3
Manufacturer specification
Configuration: DM-JH17-51-2EC; Eight equally spaced threaded holes on the rear outer circle. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing8-M3
Rear housing outside diameter callout
70
Manufacturer specification
Configuration: DM-JH17-51-2EC; Diameter of the rear housing shown in the side view. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing70
Rear m4 mounting restriction
Do not use the rear-cover M4 threads to connect load-bearing structures
Manufacturer specification
Configuration: DM-JH17-51-2EC; Manufacturer warns that using these holes for load-bearing connections can damage the rear cover.
DAMIAO JH17 mechanical drawing不建议后盖M4螺纹孔用作承载结构件的连接 易造成后盖结构损坏
Rear mounting angular offset
37.50 deg
Manufacturer specification
Configuration: DM-JH17-51-2EC; Rear-view angular offset, in degrees. The angle unit is explicitly printed.
DAMIAO JH17 mechanical drawing37.50°
Recommended motor overtemperature setting maximum
90 degC
Manufacturer specification
Configuration: DM-JH17-51-2EC; Configurable protection setting; recommended maximum 90 degrees C. Overheating exits enabled mode.
DAMIAO JH17 technical parameter table电机过温防护,根据使用需求设定,建议不超过90°C,过温电机将退出“使能模式”
Recommended overvoltage protection setting maximum
54 V
Manufacturer specification
Configuration: DM-JH17-51-2EC; Configurable protection setting; recommended maximum 54 V. Overvoltage exits enabled mode. This is not the supported operating-voltage maximum.
DAMIAO JH17 technical parameter table电机过压防护,根据使用需求设定,建议不超过54V,过压将退出“使能模式”
Reduction ratio
51:1
Manufacturer specification
Configuration: DM-JH17-51-2EC; Manufacturer ratio notation retained.
DAMIAO JH17 technical parameter table减速比 51:1 | 101:1
Supply-voltage floor in undervoltage instructions
20 V
Manufacturer specification
Configuration: DM-JH17-51-2EC; Protection guidance says the supply is not below 20 V and exits enabled mode below a configured threshold. The normal supported range remains 24–48 V; 20 V is not asserted to be a new operating-range minimum.
DAMIAO JH17 technical parameter table电机欠压防护,若电源电压低于设定值,则退出“使能模式”,电源电压不低于20V
Supported supply voltage
24–48 V
Manufacturer specification
Configuration: DM-JH17-51-2EC; Supported range from the rated-voltage row; protection threshold guidance is recorded separately.
DAMIAO JH17 technical parameter table额定电压 24V(支持24-48V)
Thermal protection
Dual temperature protection
Manufacturer specification
Configuration: DM-JH17-51-2EC; Exact-model official product-page feature statement.
DM-JH17-51-2EC / DM-JH17-101-2EC_谐波关节电机_产品中心_深圳市达妙科技有限公司具有双温度保护功能。
Through-bore diameter tolerance callout
15 ±0.10
Manufacturer specification
Configuration: DM-JH17-51-2EC; The bore is identified as through. Drawing linear units are not printed in this image; this is a literal callout, not an inferred millimetre specification.
DAMIAO JH17 mechanical drawing⌀15 ±0.10